Anilam crusader ll L
Set the following parameters on the machine
AUX 2767
AUX 2772
AUX 2784
AUX 2790
AUX 2700
AUX 2701
To set the controller in the Drip feed mode
Drip feed is not available on this Controller
Set the following parameters on the PC
General settings
Machine name
MCH-1
Control system
Crusader
Machine ID
01
Time out (sec)
5
Control program start
M82
Control program end
M30
Is DNC required
Yes
DNC settings
Port Number
COM2 (or any free COM port)
Baud rate
1200
Data bits
7
Parity
Even
Stop bits
2
Handshake
None
Filter null characters
Yes
Transmit settings
Transmit directory
Specify folder to store programs to be transmitted to the machine
Wait period at start of transmission
10.00
Wait period after transmitting program
5.0
Size of transmit packet
0
Delay period after each packet
0
Wait for XON before transmitting program
No
Drip feed
Off
Transmit comments?
Yes
Comment start character
(
Comment end character
)
Translation mode for CR
Transmit as CR
Translation mode for LF
Transmit as LF
Program start string
Program end string

 
Receive settings
Receiving directory
Specify folder to store programs coming from machine
Wait period before receiving program
75.0
Wait period after receiving program
5.0
Transmit XON before transmitting program
No
Auto compare and save
Yes
Acknowledgements and errors
Do not transmit
Translation mode for CR
Ignore
Translation mode for LF
Save as CRLF
Acknowledgement / Error message start
Acknowledgement / Error message end
Ignore control characters other than CR-LF
Yes
To set the PC in the Drip feed mode
Drip feed is not available on this controller.
Parameter settings on controller
Procedure for setting:
Press MANUAL button.
Press AUX button and the required number for AUX code.
Press START button.
Press AUX button and enter the next AUX code and continue like this for all codes in order of
their respective groups.
Group 1
AUX 2765
Sets 5 data bits.
AUX 2766
Sets 6 data bits.
AUX 2767
Sets 7 data bits.
AUX 2768
Sets 8 data bits.
Group 2
AUX 2770
Sets NO PARITY
AUX 2771
Sets ODD PARITY
AUX 2772
Sets EVEN PARITY
Group 3
AUX 2780
Sets baud rate to 110 bits/sec
AUX 2781
Sets baud rate to 150 bits/sec
AUX 2782
Sets baud rate to 300 bits/sec
AUX 2783
Sets baud rate to 600 bits/sec
AUX 2784
Sets baud rate to 1200 bits/sec
AUX 2785
Sets baud rate to 1800 bits/sec
AUX 2786
Sets baud rate to 2400 bits/sec
AUX 2787
Sets baud rate to 4800 bits/sec
AUX 2788
Sets baud rate to 9600 bits/sec
AUX 2789
Sets baud rate to 19200 bits/sec
Group 4
AUX 2790 NO Handshake
AUX 2791 Set to Software Handshake ( Xon/Xoff)
AUX 2792 Set to Hardware Handshake( DTR/RTS )
Group 5
AUX 2700 Transfer of data from crusader to external equipment in RS-274 format
AUX 2701 Receive data at crusader from external equipment RS-274 format
AUX 2702 Transfer data from crusader to external equipment in Anilam format

 
For Proper communication between PC and CNC, set the following parameters :
AUX 2767
7 DATA BITS
AUX 2772
EVEN PARITY
AUX 2784
1200 BAUD RATE
AUX 2790
NO HANDSHAKE
AUX 2700
TRANSFER OF DATA FROM CNC TO PC IN RS-274 FORMAT
AUX 2701
RECEIVE DATA FROM PC TO CNC IN RS-272 FORMAT
Cable connection
If the PC has 9 pin connector

If the PC has 25 pin connector